Crypto WF200 Installationsanleitung

WWFF220000 802.11g Wireless Four Port Ethernet ADSL2+ Modem Router MMaannuuaall Version 1.0

WF200 802.11g Wireless Router 10 1) Select Gateway tab and click OK 2) Then, select DNS Configuration tab and select Disable DNS then

WF200 802.11g Wireless Router 11 Option2: Configure IP Manually 1) At IP Address tab, select Specify an IP address, set default IP add

WF200 802.11g Wireless Router 12 Under DNS Configuration tab, select Enable DNS and add DNS values (192.168.1.1) in DNS Server Search Ord

WF200 802.11g Wireless Router 13 Step 2: Right click Local Area Connection (your local network hooked up with ADSL router) and select

WF200 802.11g Wireless Router 14 Configure IP Automatically: Step 4: Select Obtain an IP address automatically and Obtain DNS server ad

WF200 802.11g Wireless Router 15 For Windows XP Step 1: Click Start then select Control Panel. Step 2: Double-click Network Connections

WF200 802.11g Wireless Router 16 Step 3: Right-click Local Area Connection (local network your ADSL hooked up with) and select Properties

WF200 802.11g Wireless Router 17 Configure IP address Automatically: Step 5: Select Obtain an IP address automatically and Obtain DNS

WF200 802.11g Wireless Router 18 IP address: Fill in IP address 192.168.1.x (x is a number between 2 to 254). Subnet mask: Default v

WF200 802.11g Wireless Router 19 Step 2: Double-click Network and Sharing Center icon. Step 3: Select “Manage Network connections”.

WF200 802.11g Wireless Router 2 Contents 1. Introduction...

WF200 802.11g Wireless Router 20 Step 4: Right-click Local Area Connection (local network your ADSL hooked up with) and select Properties

WF200 802.11g Wireless Router 21 Configure IP address Automatically: Step 6: Select Obtain an IP address automatically and Obtain DNS

WF200 802.11g Wireless Router 22 IP address: Fill in IP address 192.168.1.x (x is a number between 2 to 254). Subnet mask: Default v

WF200 802.11g Wireless Router 23 3) Entry of the username and password will be displayed. Enter the default login User Name and Passwor

WF200 802.11g Wireless Router 24 Steps to navigate the Web configuration from the Site Map are summarized below. ¾ Click on Interface S

WF200 802.11g Wireless Router 25 Click an Interface Setup link to set ATM VC values, ISP Encapsulation, configure multi- connection setti

WF200 802.11g Wireless Router 26 VCI: Virtual Channel Identifier. The valid range for the VCI is 1 to 65635 (0 to 31 is reserved for local

WF200 802.11g Wireless Router 27 the fields must be in the appropriate IP form, which is 4 IP octets separated by a dot (x.x.x.x). The Rout

WF200 802.11g Wireless Router 28 LABEL DESCRIPTION Servicename Enter your Servicename for your PPPoE/PPPoA connection. Username Enter your

WF200 802.11g Wireless Router 29 5.2 LAN There are the IP settings of the LAN Interface for the device. These settings may be referred to a

WF200 802.11g Wireless Router 3 6.2 Routing...

WF200 802.11g Wireless Router 30 Direction: Select the RIP direction from None, Both, In Only and Out Only. Multicast: IGMP (Internet Grou

WF200 802.11g Wireless Router 31 5.2.5 DNS Relay The DNS Configuration allows the user to set the configuration of DNS. DNS Relay Select

WF200 802.11g Wireless Router 32 5.3 Wireless 5.3.1 Access Point Settings Access Point: Select this section for Activated or Deactivated

WF200 802.11g Wireless Router 33 5.3.2 Multiple SSIDs Settings SSID: The SSID is a unique name to identify the ADSL Router in the Wireless

WF200 802.11g Wireless Router 34 6 Advanced Setup 6.1 Firewall User can enable or disable firewall featur

WF200 802.11g Wireless Router 35 Destination IP Address: This parameter specifies the IP network address of the final destination of pack

WF200 802.11g Wireless Router 36 Virtual Circuit (VC): The Virtual Circuit (VC) properties of the ATM VC interface identify a unique path

WF200 802.11g Wireless Router 37 Outside This refers to the host on the WAN. Local This refers to the packet address (source or destinati

WF200 802.11g Wireless Router 38 address. c. Many-to-Many Overload: In Many-to-Many Overload mode, the device maps multiple local IP addre

WF200 802.11g Wireless Router 39 with single IP will use the same Virtual Server rules. Start & End port number: Enter the specific St

WF200 802.11g Wireless Router 4 10.5 Problems with WAN Interface...57 10.

WF200 802.11g Wireless Router 40 6.4 QoS QoS (Quality of Service). This option will provide better service of selected network traffic ov

WF200 802.11g Wireless Router 41 Port-Based VLAN: each physical switch port is configured with an access list specifying membership in a se

WF200 802.11g Wireless Router 42 6.6 ADSL Select this option to set ADSL Mode and ADSL Type information. ADSL Mode: Select which mode your

WF200 802.11g Wireless Router 43 7. Access Management 7.1 ACL Go to Access Management Æ ACL to enable remote

WF200 802.11g Wireless Router 44 [Note] 1. You must set one ACL index to access your router via LAN interface. If you don’t, your router

WF200 802.11g Wireless Router 45 Filter Type: You can select IP/MAC Filter, Application, and URL Filter type. IP/MAC Filter Set Index: Th

WF200 802.11g Wireless Router 46 allowed Protocol: Select the protocol to filter. Choices are TCP, UDP, and ICMP. Rule Unmatched: Choices a

WF200 802.11g Wireless Router 47 7.3 SNMP The Simple Network Management Protocol (SNMP) is used for exchanging information between network

WF200 802.11g Wireless Router 48 eliminates the need to manually configure port forwarding for the UPP enabled application. If you don’t w

WF200 802.11g Wireless Router 49 Configuration Servers (ACS) and establish the configuration automatically. Accordingly other service funct

WF200 802.11g Wireless Router 5 1. Introduction 1.1 Introduction This full rate Wireless ADSL2+ rou

WF200 802.11g Wireless Router 50 8. Maintenance 8.1 Administration There is only one account that ca

WF200 802.11g Wireless Router 51 time zone and Greenwich Mean Time (GMT). Daylight Saving: Choose “Enabled” or “Disabled” to use daylight s

WF200 802.11g Wireless Router 52 8.5 Diagnostic The Diagnostic Test page shows the test results for the connectivity of the physical lay

WF200 802.11g Wireless Router 53 [Device Information] Firmware Version: This filed displays current firmware version. MAC Address: The MAC

WF200 802.11g Wireless Router 54 error rate performance will improve, but the data rate will decrease. Conversely, if the SNR Margin is dec

WF200 802.11g Wireless Router 55 [Ethernet] The Ethernet screen gives you information on how much data your router has transmitted and re

WF200 802.11g Wireless Router 56 10. Troubleshooting If the router does not function properly, first ch

WF200 802.11g Wireless Router 57 3 Check that you have enabled web service access. If you have configured a secured client IP address, you

WF200 802.11g Wireless Router 58 the user name and password, the MAC address or the host name. 2 The username and password apply to PPPoE

WF200 802.11g Wireless Router 59 11. Technical Support For technical information and support please contact us: Web Site: www.crypto.gr

WF200 802.11g Wireless Router 6 z ITU-T G.992.2 (G.lite) z G.994.1 (G.hs, Multimode) z ITU-T G.992.3 (ADSL2 G.dmt.bis) z ITU-T G.992.4

WF200 802.11g Wireless Router 7 z Web-based GUI Configuration / Management z Command-line Interpreter (CLI) z SNMP support (V.1 and V.2C

WF200 802.11g Wireless Router 8 z RJ45 Ethernet Port 2.2 Package Contents z Wireless ADSL2+ Router z RJ-45 Ethernet cable z RJ-11 Pho

WF200 802.11g Wireless Router 9 3. Connecting Wireless ADSL2+ Router via Ethernet Your router can be managed from anywhere with